Home > Error Code > 2131 Error Code

2131 Error Code

Contents

Uninstall DFS if required.NERR_DfsCantRemoveDfsRoot 2683A child or parent directory of the share is already in a Dfs.NERR_DfsChildOrParentInDfs 2690Dfs internal error.NERR_DfsInternalError 2691This computer is already joined to a domain.NERR_SetupAlreadyJoined 2692This computer is Target timeout This error happens whenever the JTAG tries to read a target device but it does not respond to the requests after an arbitrary number of retries. Often, this is associated with the optical drive, and it may occur if you are attempting to burn a CD. Also, when the driver's attempt to HALT the core fails, it checks to see whether it is due to memory-hang condition. this content

Correct the target configuration file. The explanation is: An attempt to connect to the XDS110 failed. lower TCLK). If the issue happens after the code loaded successfully but never reaches main(), the problem resides on the application code (bad initialization of the device, watchdog timers not being refreshed, invalid http://www.error.info/windows/optical-drive-2131.html

Error Code 2131 Itunes

The network cannot access a shared memory segment.NERR_ShareMem 2105A network resource shortage occurred.NERR_NoNetworkResource 2106This operation is not supported on workstations.NERR_RemoteOnly 2107The device is not connected.NERR_DevNotRedirected 2114The Server service is not started.NERR_ServerNotStarted NO overwrites all user setup, incl. C28x the debug probe reported an error This error is commonly associated with C28x devices and is usually associated with a range of hardware or firmware problems that prevent the JTAG If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g.

In this case, it is absolutely unpredictable what types of messages can be shown. Reset the device, and retry the operation. Review the Emulation FAQ 6. Network Error Codes Pdf This can have several sources: The Windows device drivers are not properly installed or failed to initialize.

The value is '-260' (0xfffffefc). XDS510 Spectrum Digital: ** BoardFilePath: C:\Users\user\AppData\Local\TEXASI~1\CCS\CCSV6_~3\0\0\BrdDat\testBoard.dat ** Resetting Emulator ERROR -- XDS510-USB Emulator not connected/enumerated XDS510 (not Spectrum Digital): An error occurred while soft opening the controller. -----[An error has occurred However, if the error happens later in the debug session the reasons are different (perhaps the reliability of the JTAG connection due to noise, etc.). The utility will now report only the count of failed tests.

Trouble Halting Target CPU: Error 0x80001820/-2062 Fatal Error during: Execution, Timeout, Target, Cannot halt the processor This is an error that was recovered but the code integrity is unknown. Error 1326 Another fix is to check to see if there is new firmware being offered for the optical drive. The title is 'SC_ERR_OCS_PORT'. Confirm debug probe configuration and connections, reset the debug probe, and retry the operation.

Error Code 1231

For XDS100, please check section 2.6 (troubleshooting) of the XDS100 page. https://msdn.microsoft.com/en-us/library/windows/desktop/aa370674(v=vs.85).aspx By doing this step-by-step operation it is possible to precisely know where the issues are happening: If the issue happens during the Debugger Launch phase, check sections 4 and 5 of Error Code 2131 Itunes Download Spyware Remover - scans and removes all spyware, adware or viruses on your system. Network Error Codes If you are working with electronics that are near motors or other electrical components that could induce currents, then shielding and isolation may be important.This typically manifests itself as the connection

It happened on drive D: TSSTcorp CDDVDW TS-L632H on CDR media at speed 0X.Any ideas??? news Please try the request again. If so, it tries to clear that condition and returns a warning (a ready-hang condition) and proceeds. Test 3 Word 0: scanned out 0xFE03E0E2 and scanned in 0x80F83880. Network Error Codes List

Also, loose cable connections are more difficult to troubleshoot, as they may work fine at certain times. The value is '-150' (0xffffff6a). Power-cycle the board. have a peek at these guys Test 3 Word 0: scanned out 0xFE03E0E2 and scanned in 0xFC07C1C5.

Error connecting to the target: (Error -2131 @ 0x0) Unable to access device register. Http Error Code Also, the JTAG clock speed may be too high. 7. In other circumstances the JTAG debugger could not precisely determine the cause of the memory bus error ("may be hung"), therefore it is very difficult to define where this issue is

This test will be applied just once.

The disc itself may be corrupted, just put a new one in and try again. Check all hardware - details are shown in the section Hardware checklist below. This error manifests itself in several messages: These are unrecoverable errors during connection that prevent the JTAG debugger from gaining control over the core. Windows Error Codes However, if there is a more severe power outage on the device, the JTAG debugger is unable to bring it out of this mode: Error: (Error -1155 @ 0x0) Device may

This has failed because the built-in limit for the maximum number of attempts when polling the JTAG scan-path has been exceeded. Check the minimum password length, password complexity and password history requirements.NERR_PasswordTooShort 2246The password of this user is too recent to change.NERR_PasswordTooRecent 2247The security database is corrupted.NERR_InvalidDatabase 2248No updates are necessary to If the issue happens during connect phase, check the Troubleshooting the connect phase section below. http://rlegsoftware.com/error-code/206-error-code-db2.php The JTAG debugger is not powered (some variants of XDS560 and XDS560v2).

IcePick_C_0: Error connecting to the target: (Error -611 @ 0x0) A request was received to control the JTAG state or to execute a JTAG scan while the debug probe is in In more unusual circumstances it may also be required to update the device support in CCS or the JTAG debugger device drivers. This documentation is archived and is not being maintained. Downloads and tools Windows 10 dev tools Visual Studio Windows SDK Windows Store badges Essentials API reference (Windows apps) API reference (desktop apps) Code samples How-to guides (Windows apps) Learning resources

If error persists, confirm configuration and/or try more reliable JTAG settings (e.g. The explanation is: A required dynamic library could not be located. If that simple fix doesn’t work, then it may be that you have incorrectly installed iTunes. To learn more about this error, please check out our Error Analyzer software.

These have been specifically designed to help repair this error; Download Windows Software Update - updates the drivers that control your computer. All the ARM connectors (10 and 20 pin) do not have the guide pin, therefore check both the placement of the pin 1 and the displacement of the connector by an A generic error is shown at: Lost control of device execution state For MSP432 check the remark at: Invalid device ID For Wireless connectivity devices, check this e2e forum thread For Error connecting to the target: (Error -1143 @ 0x0) Device core was hung.

We appreciate your feedback. If you are unable to connect to a specific core of an SoC device (IVAHD, EVE, IPUSS, PRUSS, etc.), you may need to release it from reset. The title is 'SC_ERR_FTDI_OPEN'.