Home > Error Codes > 2000 Jeep Error Codes

2000 Jeep Error Codes

Contents

P0720 (M) Low Output SPD Sensor RPM, Above 15 mph The relationship between the Output Shaft Speed Sensor and vehicle speed is not within acceptable limits. Possible vacuum leak. Prolonged driving with the "Malfunction Indicator Light" or "Check Engine" light on could cause further damage to the emission control system. Rating is available when the video has been rented. weblink

P0204 (M) Injector #4 Control Circuit Injector #4 or INJ 4 injector bank output driver stage does not respond properly to the control signal. This is a feature!A loose gas cap may light up the Check Engine light! (Thanks, Lyn Clark) On older cars (1980s-1990s) Instructions and codes Late-1990s and newer cars You may want Connect scan tool to the 16-pin data link connector (DLC) located near the steering column. Code 76-Ballast bypass relay-open or short in fuel pump relay circuit.

Jeep Wrangler Error Codes

P1292 CNG Pressure Sensor Voltage Too High Compressed natural gas pressure sensor reading above acceptable voltage. DTC's are the results of a system or circuit failure, but do not directly identify the failed component or components. 0010-0099 0100-0199 0200-0299 0300-0399 0400-0499 0500-0599 0600-0699 0700-0799 0800-0899 1100-1199 1200-1299 trans. P0523 Oil Pressure Voltage Too High Oil pressure sending unit (sensor) voltage input above the maximum acceptable voltage.

P0519 Idle Speed Performance A rationality error has been detected for target RPM not met during drive idle condition. P0236 (M) Map Sensor Too High Too Long Problem detected in turbocharger wastegate. P0562 Charging System Voltage Too Low Supply voltage sensed at ECM too low. Ford Error Codes Related Links Skip navigation UploadSign inSearch Loading...

P0072 Ambient Temp Sensor Low Input Ambient temperature sensor input below the minimum acceptable voltage. Jeep Liberty Error Codes Do this sequence three times. Code 1018-No serial data from the ECU. http://jeep-xj.info/HowtoECUcodes.htm P0020 A Camshaft Position Actuator Circuit (Bank 2) P0021 A Camshaft Position - Timing Over-Advanced or System Performance (Bank 2) P0022 A Camshaft Position - Timing Over-Retarded

No camshaft position signal detected during engine cranking. 61 BARO solenoid failure 62 Controller failure. Toyota Error Codes P0355 (M) Ignition Coil # 5 Primary Circuit Peak primary circuit current not achieved with maximum dwell time (High Impedence). P0404 EGR Position Sensor Rationality EGR position sensor signal does not correlate to EGR duty cycle. P0116 No Message A rationality error has been detected in the coolant temp sensor.

Jeep Liberty Error Codes

It could also affect fuel economy and driveability. Code 43-Ignition coil #1,2, or 3 primary circuits-peak primary was not achieved within the maximum allowable dwell time. Jeep Wrangler Error Codes P0310 (M) CYLINDER #10 MISFIRE Misfire detected in cylinder #10. Jeep Error Codes List lee williams 614,157 views 4:33 97 Cherokee OBDII Key Trick - Duration: 1:24. 89Laredo 30,554 views 1:24 DIY Instrument Cluster removal Jeep Tj - Duration: 4:02.

Was the fuel pressure checked with a DRBIII pressure transducer? http://rlegsoftware.com/error-codes/2000-chevrolet-error-codes.php to high or low. P0205 (M) Injector #5 Control Circuit Injector #5 output driver stage does not respond properly to the control signal. P1689 (M) No Communication Between ECM and Injection Pump Module Data link circuit failure between ECM and fuel injection pump. Jeep Jk Error Codes

COMMUNICATIONS ERROR - If the cluster receives no lamp-on or lamp-off messages from the PCM for twenty consecutive seconds, the MIL is illuminated by the instrument cluster. P0153 (M) 2/1 Sensor Slow Response Oxygen sensor response slower than minimum required switching frequency. Loading... http://rlegsoftware.com/error-codes/2000-gm-error-codes.php Thank you, great reference resource. 03-09-2012, 09:12 AM #7 luke1999 Newbie Join Date: Mar 2012 Location: midwest Posts: 5 My Photos 2001 Cherokee Engine: 4.0 Transmission: auto Transfer

We do ask that you please read the info available on the site first so that we can help reduce repeat questions. Honda Error Codes See applicable service manual section (21) for solenoid assembly replacement directions. P0107 (M) Map Sensor Voltage Too Low MAP sensor input below minimum acceptable voltage.

After that, a series of tests show up: "Code 1", "Code 2" and "Code 3" which test the gauges, lights and LEDs in the instrument panel, including the trip-computer/compass.

Sign in 23 3 Don't like this video? trans. Thanks, Dan 02-21-2011, 08:22 AM #5 Dan_in_WA Junior Member Join Date: Dec 2010 Posts: 35 My Photos 1994 Cherokee Engine: 4.0L Transmission: Automatic Transfer Case: Yes. Nissan Error Codes Code 1055-Coolant temperature sensor line high.

Dodge, Jeep, Chrysler, Ram, and Mopar are trademarks of Fiat Chrysler Automobiles.

Supercharged Rebel TRX: 100+ mph, offroad (video) Why Texas matters 2017 Ram 1500 Lone Star Silver (video) Looking back, P0204 (M) Injector # 4 Control Circuit Injector # 4 or INJ 4 injector bank output driver stage does not respond properly to the control signal. P0311 (M) Cylinder # 12 Misfire Misfire detected in Cylinder # 12. this content P0320 (M) No RPM Signal to PCM (Crankshaft Position Sensor Signal to JTEC) A CKP signal has not been detected at the PCM.

Code 1209-Injector open. Dodge, Jeep, Chrysler, Ram, and Mopar are trademarks of Fiat Chrysler Automobiles.

Supercharged Rebel TRX: 100+ mph, offroad (video) Why Texas matters 2017 Ram 1500 Lone Star Silver (video) Looking back, P0123 (M) Accelerator Position Sensor (APPS) Signal Voltage Too High APPS voltage input above the maximum acceptable voltage. P0136 (M) 1/2 O2 Sensor Heater Circuit Malfunction Oxygen sensor heater element malfunction.

P0119 Engine Coolant Temperature Circuit Intermittent Engine coolant temperature sensor input above the maximum acceptable voltage. ImperialCrown wrote that the cam position is used mainly to synchronize fuel injectors, the crank position is needed to know when to spark. The specific fault must be acquired from the EATX via a DRBIII tool. (Input or Output Speed Sensor failures often cause this code and are a common failure part on WJ Switch Circuit High P1875 4WD Low Switch Circuit Electrical P1884 TCC Enable/Shift Light Circuit P1886 Shift Timing Solenoid P1887 TCC Release Switch Circuit P1890 ECM Data Input Circuit P1890 Throttle Position

Code 1033-Idle speed increase line low. P0360 Ignition Coil J Primary/Secondary Circuit Peak primary circuit current not achieved with maximum dwell time (high impedance). trans. P0234 (M) Turbo Boost Limit Exceeded Problem detected in turbocharger wastegate.