Home > Error Codes > 20205 Communication Error

20205 Communication Error

Contents

Refer to your scanner manufacturer's documentation. 20093 KGERRMECHANICALERROR KGERR_MECHANICALERROR Peripheral mechanical malfunction. The invalid portion is probably the "yyy." 20142 KGERRININOENTRY KGERR_ININOENTRY The entry in an INI file section is missing. No accelerator board. 20172 KGERRNOTREADY KGERR_NOTREADY Device is not ready. 20173 KGERRTONERLOW KGERR_TONERLOW Printer toner is low. Check that the correct drivers are installed and that the accelerator is configured correctly. 20015 KGERRCANTOPENDEVICE KGERR_CANTOPENDEVICE Cannot open device.

This is a 16-bit problem. Check the KPrnt SourceCap property and set Source accordingly. 20066 KGERRBADPARAMCOMBO KGERR_BADPARAMCOMBO Invalid parameter combination. Refer to your scanner manufacturer's documentation. 20092 KGERROPTICSERROR KGERR_OPTICSERROR Peripheral optics malfunction. Possible conflict with the selected engine or the engine does not exist. http://forums.kofax.com/viewtopic.php?f=66&t=17633

Kofax Error Codes

The system returned: (22) Invalid argument The remote host or network may be down. Recalibrate the scanner. This error reflects a status returned by the scanner. Check your printer manufacturer's documentation. 20174 KGERRDEVICEFAIL KGERR_DEVICEFAIL Pixel translations.

Check the KPrnt DestinationCap and JogPositionCap properties and set Destination and JogPosition accordingly. 20082 KGERRBADORIENT KGERR_BADORIENT Invalid orientation. Check the ScanContrastCap and ScanModeCap properties and set ScanContrast and ScanMode accordingly. 20084 KGERRUNKNOWNERROR KGERR_UNKNOWNERROR Unknown error. I uploaded it from one computer on the other side of the house and started the print from a computer just beside the printer. Abb Irc5 Manual Pdf korpx commented Sep 13, 2013 Glad to help, sorry it didn't lead to anything.

Now, let's try the following. Check the KScan ScanDensityCap property and set ScanDensity accordingly. 20055 KGERRBADCONTRAST KGERR_BADCONTRAST Invalid contrast. For example, you might have defined a picking rectangle larger than your image. This Site KPrnt is not sending information to the printer. 20116 KGERRBADSEQUENCE KGERR_BADSEQUENCE Bad sequence.

Either the drivers have not been installed or the accelerator is not operational. Abb Irc5 Troubleshooting Manual Check your drivers and resource files. 20104 KGERRINVALIDACTIVEZONE KGERR_INVALIDACTIVEZONE Invalid active zone. Copies may be made for internalpurposes.While every effort has been made to ensure that the information in this manual is accurate, noresponsibility can be accepted for errors or omissions contained within Some days the error seem more frequent.

Abb Error Codes

Usually, a more descriptive error is generated. http://support.blackberry.com/kb/articleDetail?ArticleNumber=000028704 Unreserve the current device and try again. 20013 KGERRDEVICENOTRESERVED KGERR_DEVICENOTRESERVED Device is not reserved Reserve the device and try again. 20014 KGERRCANTOPENBOARD KGERR_CANTOPENBOARD Cannot open engine. Kofax Error Codes These types of errors are generally NOT caused by a developer. Abb Robot Fault Codes Back to top ↑ Workaround Bypass the hardware load balancer with a hosts file entry so that the BlackBerry Enterprise Server may communicate directly with a single Client Access Server.

This is a general error for invalid setting combinations. Check the KScan ScanDuplexCap property before setting ScanDuplex. These type of errors are often caused by the following conditions: product is not properly installed. The secondary board must be at least as fast as the primary board. Abb Irc5 Error Codes

The system returned: (22) Invalid argument The remote host or network may be down. Verify the path and file name specified in the IniFileName properties for each control. 20018 KGERRINIDOESNOTEXIST KGERR_INIDOESNOTEXIST .INI file does not exist. Check your KPrnt source rectangle properties (such as SourceRectHeight and SourceRectWidth). 20113 KGERRINVALIDDESTINATIONRECT KGERR_INVALIDDESTINATIONRECT Invalid destination rectangle. korpx commented Aug 27, 2013 I get these errors too, pretty often. 4 times tonight out of maybe 12 prints.

Faster scanners require a KF-9275. Abb Fault Codes When a load balancer is implemented with a Microsoft Exchange Server, TCP traffic is given a timeout value. I seem to at least be able to observe it occasionally when printing from the Pi, so I might get an idea soon.

Check the scanner driver and scanner capabilities. 20072 KGERRBADLONGSCAN KGERR_BADLONGSCAN Long scan is not supported or the scanner is not configured for long scan operations.

It looks just the same like a successful case. Set the BICCFG environment variable to the location of the BIC.CFG file. The load balancing appliance follows TCP Stack Hardening guidelines that force any open TCP traffic that is passing through it and is over the 5-minute threshold to be closed. Abb S4c Controller Manual Check your KPrnt printable area properties (such as PrintableAreaHeight and PrintableAreaWidth) and your KPrnt destination rectangle properties (such as DestRectHeight and DestRectWidth). 20114 KGERRUNABLETOCREATEBITMAP KGERR_UNABLETOCREATEBITMAP Unable to create bitmap.

Error 'Network problems are preventing connection to the Microsoft Exchange Server computer.', LowLevelError 6, Component 'Microsoft Exchange Server Information Store', Context 1300 [20301] (06/11 16:47:37.522):{0x2308} {[email protected]} Unable to save configuration settings Back to top ↑ Follow Us BlackBerry Blog Facebook Twitter Youtube Flickr Customer Service Contact Us Support Corporate Company Investors Careers News Customer Service Corporate Responsibility Legal Info Overview Accessibility Trademarks Reload to refresh your session. The color bit for the image is invalid or corrupted. 20059 KGERRBADBITSEX KGERR_BADBITSEX Invalid bitsex.

Instead, refer to Article 26490 if this is not helpful in determining configuration options, the required settings can be described as source-IP based persistent routing. Check your PATH statement. 20048 KGERRCONTROLNOTCONNECTED KGERR_CONTROLNOTCONNECTED Control not connected. Check the physical configuration of the scanner. 20074 KGERRBADSRCSIZECOMBO KGERR_BADSRCSIZECOMBO Invalid paper source/paper size combination. The name of the hardware load balancer will match the Exchange 2010 CAS Array name.   Example: 10.0.0.25 (IP address of the CAS Node) CASArray.domain.com (Fully Qualified Domain Name of the CAS