Dec 22, 2015 | HP DesignJet 1055CM Plus InkJet Plotter... 1 Answer What does the error message EI0 1 Mean on the 8150dn printer? Remove all EIO devices from the printer.8. Have a manual for Printers & Copiers? If the issue reoccurs, try installing a known good duplexer from another compatible unit, if possible. http://rlegsoftware.com/error-hp/81-0180-error.php
Action NOTE: Press the ? (Help) button for detailed information about clearing the jam. Printing can continue, but behave unexpected in response to the changed settings. It may need a firmware upgrade, you may need to adjust settings or even change the slot. Turn power off and reseat the card. http://geekhardlife.com/81-0180-eio-1-error-on-printer/
For enterprise products go to Hewlett Packard Enterprise.© Copyright 2016 HP Development Company, L.P. Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Remove all non-HP paper-handling devices. 79.00fe Printer Error Hp 5100 NOTE: If most of the paper is still inside the printer, it might be easier to remove it through the top-cover area.
top 21 PAGE TOO COMPLEX Description The data (dense text, rules, raster or vector graphics) sent to the printer was too complex. The second slot might be a hard drive but is usually open. Sign in Share More Report Need to report the video? Continued n If the Error Code disappeared after removing the EIO Card, then switch the Printer OFF and reinstall the EIO Card, making sure that the two installation screws are completely tightened.
the error message continues to appear 1. Hp Laserjet 4250 Error Codes Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! Power up and try the printer. If the message persists, contact HP Customer Support.
The deflector is behind the rear output bin door and is made of black plastic. http://www.fixya.com/support/t3128339-81_0180_eio_1_error_code_hp_laserjet This solution may have done the trick...maybe I wore out a contact on slot 1 ! 81.0180 Eio 1 Error Hp 5500 Figure 37: Removing the rear output bin Firmly grasp each side of the fuser. Eio Card Hp Printer Kęstutis Bivainis 277 views 2:28 HP4000/4050/4100/5000 Network config - Duration: 1:48.
Have a manual for HP LaserJet 5500DN Printer? When handling DIMMs, either wear an anti-static wrist strap or frequently touch the surface of the DIMM anti-static package, then touch bare metal on the printer. The printer software system is corrupt. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework. Eio 1 Error Hp Laserjet 4600
Description A fuser error has occurred. Verify the stacker or stapler/stacker is installed correctly and that its electrical connector is seated in the connector on the printer. In some cases, electrical noise in the cable can corrupt data during transmission to the printer. Look for the jam in another location, contact HP, or contact an authorized service provider.
top 64 PRINTER ERROR For help press? Jetdirect 620n You can't post answers that contain an email address. If the paper is folding into an accordion shape, make sure the print cartridge shutter (black plastic hinged piece covering the drum) located on the bottom of the cartridge opens when
Loading... I've unmounted and reseated it several times in the same slot, (even baked the card a couple times). For example, pressing Cancel Job cancels the job. alternates with 64 PRINTER ERROR To continue turn off then on 66.00.15 EXTERNAL DEVICE FAILURE 66.12.XX OUTPUT DEVICE FAILURE For help press? 68.X PERMANENT STORAGE ERROR For help press ?
Please enter a valid email address. Does anybody have any experience of the error ? Was the information on this page helpful? These messages typically alternate with the “Ready” or “Status” messages and remain displayed until the (Select) is pressed.
Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! X Description 1- Unknown misprint error 2- Beam-detect misprint error 4- No VSYNC error 7- Feed delay error 9- Signal noise error Action Press the (Select) button to continue or press Remove the duplexer if installed. Corrective Action: Refer to System Error Code 070100 System Error: 070100 XXXXXXXX (Non-Continuable) Problem Description: Firmware Error.
Press the Check button one more time to Print Menu Map and then press the Check button. Comment Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product? To exit the Help system, press (Help) again. The issue can be caused by a firmware error, invalid print commands, corrupt data, invalid operations, poor quality parallel cables, poor connections or specific applications.
Corrective Action: Power the Printer OFF and ON again to see if the System Error disappears. If the above action does not solve the issue, contact HP or authorized service provider. Print a Configuration page and verify that the tray settings match the media in the tray. prev next 3 Points Related Questions: 1 Answer What does the error message EI0 1 Mean on the 8150dn printer?
Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. Ask Loading...Oops :Please try again. Figure 5: Rotating the paper guide Replace the entrance cover and close Tray 1. Or just drag it here!
Remove the EIO Card (if installed) and make sure that the Hard Disk Drive is installed correctly by pushing it firmly inwards and checking that the two installation screws are completely Then reboot printer AND computer, reconnect cables, and try printing again. 6. top 59.2 MAIN MOTOR ROTATION ERROR Description The printer main motor is not functioning correctly. The second slot might be a hard drive but is usually open.
Remember to reconnect all cables that connect the printer to the network or computer.12. Action If the printer displays this error then please contact HP Support. Switch the Printer ON again.