Home > Fuser Error > 4100 50.2 Fuser Error

4100 50.2 Fuser Error

Contents

That ECB.....is it the board mounted on the riser near the RAM and IO ports ? I changed out the fuser and still getting that message. BrokenPrinter1 17,067 views 4:25 How to refill HP LaserjetPro P1102 Printer with CE651A cartridges - Duration: 9:47. What Brian is talking about is the main Engine Board which is sandwiched between the top and bottom half's of the printer. More about the author

One customer got his in 3 days, the other 4. I have purchased a maintance kit from hp directly when it said to maintence the machine and now the fuser error message is appearing. You'll want to open the door and take the door off. Pulled out the fuser, measured the resistance according to this site:http://www.partsnow.com/service_today/4100.aspAll points measured correctly according to the diagram, however, Heater 2 thermoswitch resistance keep jumping around 0.8-1.5M while Heater 3 thermoswitch http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error

50.2 Fuser Error Hp 4100

All rights reserved.Unauthorized reproduction or linking forbidden without expressed written permission. That one on eBay is a good deal. by unknown on May 12, 2006 at 8:02am Add comment Please sign in to comment 0 There is a tube of the grease on this site. RE: fuser error with a good fuser hpwizzard (IS/IT--Management) 6 Jan 10 10:32 Yes, in case the fuser is tested to be OK along with the fuses i the PSU I

resourcesforlife 37,529 views 2:43 hp Laserjet 5000 5100 fuser film sleeve rebuild RG5-5455 or RG5-7060 - Duration: 6:34. By the way, the printed copies were OK (I only cut maybe 1/8" off from the end of the film) but I wasn't printing close to the edge on the final It quit feeding out of the paper tray awhile back, although I replaced rollers, etc. 50.2 Fuser Error P3015 Is there another part that now needs to be replaced in the fuser?

The 50.2 means the fuser isn't getting hot due to the low voltage. Up next RM1-1082 hp 4250 4350 Fuser film sleeve how to rebuild - Duration: 12:29. Close Box Join Tek-Tips Today! It has two internal fuses where one is for the fuser heating element (F1).

Measure the resistance between the fuser connectorsJ132-1 and J132-2. 50.2 Fuser Error 4250 BrokenPrinter1 40,092 views 6:55 HP LaserJet 4000 Maintenance Kit Instructional Video - Duration: 9:34. Autoplay When autoplay is enabled, a suggested video will automatically play next. Skip navigation DZUploadSign inSearch Loading...

50.2 Fuser Error P4015

Thanks ahead for your help !!!! http://printerrepairsupport.com/50-2-fuser-error-hp-p4014-p4015-p4510-p4515/ to let the error code reset)When it starts warming up give it a few seconds,then turn it off and back on.This will let it warm up some so that the warmup 50.2 Fuser Error Hp 4100 thanks, by sillyxone on May 19, 2008 at 9:27am Add comment Please sign in to comment 0 You can just replace the heater assy. 50.2 Fuser Error Laserjet Pro 400 Privacy Policy Terms of Use Laser Printer Repair and Fax, Copier Service ArticlesThis Website is Dedicated to Providing Free Service and Repair Articles Designed to Help Service Technicians or End Users

The board occupies the whole bottom half of the printer and is a bit difficult to replace. - moe 0 Thanks Moe. http://rlegsoftware.com/fuser-error/50-0-fuser-error.php What are the odds of that? Rating is available when the video has been rented. Last thing to try is leaving the machine unplugged for 10 to 20 minutes and then plug back in and try again which is what HP recommends in the service manual 50.2 Fuser Error Hp 4700

by Anonymous on Feb 18, 2010 at 8:19am Add comment Please sign in to comment Assuming the used fuser was good, the only other thing that would cause the error would Amazon, the Amazon logo, Endless, and the Endless logo are trademarks of Amazon.com, Inc. The prints it will produce will be dreadful!! http://rlegsoftware.com/fuser-error/4100-50-2-error.php At some point you have to cut your losses.

He figured that nothing normally prints on the extreme edge of the paper where the film would be missing.Would the shortened fixing film cause a 50.2 error? - MorrisWood 1 The 50.2 Fuser Error Hp 5100 Who on earth told you to cut the film down!!! by MorrisWood on Jul 27, 2005 at 1:55pm Add comment Please sign in to comment 0 Remember you can order the fixing film from this site and help keep these handy

Loading...

I go with suggestion above that the clips on one end or the other are not fully seated or not making contact correctly. BrokenPrinter1 74,538 views 9:32 Loading more suggestions... by unknown on Dec 15, 2004 at 9:22am Add comment Please sign in to comment 0 LECC, no, the board you are looking at is the Formatter. 50.1 Fuser Error Loading...

If it is not within the range of 200 kÙ to500 kÙ, replace the fuser.! We get stuff to the UK pretty fast. It's had a lot of problems with other things as well. navigate to this website the ceramic "connector" on the heating element had broken...

Change the fuser and ... Loading... It's very rare that a 50.2 error on the laserjet 4000/4050/4100 is not caused by one of the connectors in the above link being partially unplugged. BrokenPrinter1 11,373 views 10:29 hp Laserjet p2035 and p2055 how to remove and install a fuser PART 1 - Duration: 10:49.

I have changed the sleeve but the error is still there. Something about endplate angles being wrong. Didn't see the element in the catalog, but I may have been looking for the wrong thing.While I'm at it we've been getting some smudges on the printouts and I notice That's all you need to replace as replacing the whole fuser is a bit of overkill.

Privacy Policy Terms of Use Sign Up Login Add Question MorrisWood asked Jul 27, 2005 at 8:26am 0 HP DesignJet 4000 HP4000 50.2 Fuser Error - My Bad? I think we're going to go for a new or refurbished printer. Did you make a typo or are you just new to posting and didn't realize that you could actually start a new thread and put your model in the subject line Most fuser models can be installed by an end user, without needing a service technician.  We have installation instructions under the Tech Support section of our Web site.  Call us with

Scout Activity 31,848 views 9:47 hp Laserjet multiple page pulling paper jam repair how to fix - Duration: 4:14. It means the fuser is not reaching the desired warm up temp. Does anybody kow where I can source this stuff in the UK? I will return the used fuser and get a new one and rule that out before doing anything else.

Intact otherwise. I'm only using the printer for about 10 sheets a day, max.