Home > Fuser Error > 4v Error 50

4v Error 50

Contents

Replace the connector if it is damaged. 6. LJ4, 4+ Check and reseat laser scanner cable connections Replace laser scanner assembly 4V Check fiber optic cable from scanner to DC controller PCB Replace laser scanner assembly 4L, 4P, 5P IIISi, 4Si Check that PS1 (paper sensor) is blocked by the Latch Flag. Reseat cables to the laser/ scanner and engine controller. 4.

A fuser error has occurred. Incompatible memory card in front slot 57-2 error. Now I still get the "50 Service" error code again. The HP part# for the 200K page IIISi, 4Si maintenance kit is C2062-69001. weblink

50.0 Fuser Error

Check the fuser resistance first to confirm, but most times it will require replacement of the low voltage power supply. Reseat the formatter cable in the ECU.3. After replacement with a Toshiba lamp (not an endorsement, just what the supplier sends) the problem is gone. Press GO.

Check the printer’s configuration. 3. If the error persists, replace the fusing assembly. 8. San Rafael, CA Great that you have that part in stock and thank you for your quick reply. 50.0 Fuser Error Hp Laserjet P1007 Turn the printer off and allow it to cool down.2.

Look for bent pins or debris. The page containing the error will automatically be reprinted. 1. Replace the fuser.HP LASER PRINTER 3027M/3035 ERROR 50.X FUSER 1. Holzarbeiten Das intelligente Haus Nützliches Zubehör Links HP9810A HP97 Siemens comfoset 150 Detartrage Impressum

Repairing the HP LaserJet Series II power supply My HP LaserJet Series II In May 2009,

Check the cabling connections to the heating element. 5. 50.0 Fuser Error P1108 These heating elements are subject to failure from burned resistive heating paths and fractures of the ceramic substrate material. Verify that the fuser power cable at the back of the device is connected and the ECU is fully seated.3.Verify that the seven wire connection is firmly seated in connector J405 I would first try to get a warranty fuser from wherever you purchased the kit ...

50.0 Fuser Error Hp Laserjet P1102

Verify that the correct fuser model is installed in the product. 3. http://www.advancedlaser-hp-error-codes.com/error_50.htm Incorrect cable hookup or bad I/O port in computer. 50.0 Fuser Error intnx in a macro 5. 50.0 Fuser Error Hp Laserjet P1108 Replace the engine board.5.

Power printer off/on Excessive memory. HP LaserJet Error Codes 50-59 Message on printer displayWhat it meansWhat to do 50.X FUSER ERROR A fuser error has occurred. 1. Defective fuser.Replace the fuser ass'y 3. Replace the upper cable guide ass'y. 4. 50 Fuser Error Hp Laserjet 3050

Check the connector between the fuser and the printer. Replace the laser/scanner. 5. Replace memory PCB 53-2 - Error in rear memory slot. HP LASER PRINTER 1200, 2200, 3100 FAX, 3200 FAX, 4100, 4100MFP 1.

Bad fuser ass'y5. 50 Fuser Error Hp Laserjet 3052 II, IID Remove I/O cables. Remove memory and power up printer.

There are 4 screws, one of which has a star washer.

The procedure until here is well documented in the service manual, which can also be found on the net. There are two black screws on top of it which need to be loosened. Turn printer off then wait 20 or 30 minutes.2. 50 Fuser Error Hp Laserjet 3055 Recycle printer power.

Replace the fuser ass'y 3. Replace the power supply. A fuser error has occurred.2. Bad fuser ass'y.4.

X=6 Open fuser, heating element broken X=7 Fuser pressure release malfunction X=8 Low fuser temperature X=9 High fuser temperature 2. It can be tested with an ohm-meter, the procedure is well documented on the net, and I don’t have to repeat it here. This is one way to fix your problem. We do not sell these spare parts.We help you to create your parts sheets to request from your suppliers.

Improperly seated fuser. 2. HP LASER PRINTER 20151. There is lots more, you need the service manual to know how to disassemble it. The two printers (4200, 4300) fuser ass'y will fit in the two models but will come up with error 503.

You can print your Parts List or export to Excel to further work with him. Turn off the device to allow the fuser to cool. 8. All printers No toner cartridge installed or not fully seated Is there at least ONE sensitivity tab on the 92295A toner cartridge? 2686A/D Bad cassette microswitch Bad toner cartridge - missing Reseat connector J201 on sensor PCB Check SW101 to insure it engages when top cover is closed (NOTE!!

I may be contacted via the Sci.Electronics.Repair FAQ (www.repairfaq.org) Email Links Page. <> HP LaserJet 4 - intermittent error Plug the printer directly into the wall socket.4. While at it, also have a look at the lower PCB with the triac, mounted on a piece of tin to disperse heat. I hope the power supply is good for another 20 years now! Start | LaserJet 4L | LaserJet Series II | © 2007 Marais

Bad D.C. Replace the controller board. Check replace SIMM's 61.x Service All printers Reseat SIMM memory Replace SIMM's Replace formatter PCB 62 Service 2686A/D, II, IID, IIP, IIP+, III, IIID, IIIP, 4P Replace formatter PCB 62 Memory LJ4, 4+ Plunger missing on top cover.

No toner cartridge installed External fuser access door not closed. Start there first, is it getting hot?