Home > Fuser Error > 50 Fuser Error Cycle Power Hp Printer

50 Fuser Error Cycle Power Hp Printer

Contents

The printer will remain online. Once reported, our moderators will be notified and the post will be reviewed. Font Test To check fonts available in printer, take printer off-line and press the [Menu] button repeatedly until the TEST MENU appears. PROCESSING JOB This message is displayed when the printer is processing a print job. click site

No action required. INITIALIZING The printer is performing initialization tasks after being powered on. If the error continues, call your dealer or HP service representative. AC Power is not being provided to the fuser assembly, AC voltage is necessary to generate heat in the fuser assembly.2.

Hp Printer 50.2 Fuser Error

Activation: Through front panel menu. If the error persists, replace the heating element.5. Sent from my All-In-One Desktop.

If you switch the printer off, then on, you may lose settings (to check settings, print a self test). If printer is hooked up to uninterruptible power supply or surge protector plug straight in to wall.2. Improperly seated fuser. 4. Hp Laser Printer Error Codes If the message persists, reseat the fuser.

Try replacing the fuser.) 56.X PRINTER ERROR An incompatible combination of input/ output bins was selected. 50.3 Fuser Error Hp Printer U4-3000 (U4-3) Fuser thermistor circuit is detected as ... Hewlett-Packard LaserJet 5 / 5N/ 5M Paper Handling Unprintable Regions Left: 1/6th inch Right: 1/6th inch Top: 1/6th inch Bottom: 1/6th inch Continuous Feeding Standard : Paper Cassette [capacity: 250 sheets]. http://www.fixyourownprinter.com/posts/74908 Press [Go] if the desired size is already in the tray.

MANUALLY FEED envelope size The printer requested that an envelope be manually fed. 50.0 Fuser Error Hp Laserjet P1102 Activation: Through front panel menu. The page containing the error will automatically be reprinted. 1. Sent from my All-In-One Desktop.

50.3 Fuser Error Hp Printer

Two screws at the bottom of the supply and three screws on the plate to the left. http://www.advancedlaser-hp-error-codes.com/error_50.htm If so, could someone send me the link?Thanks Very Much,CharmedLife417 charmedlife417 has chosen the best answer to their question. Hp Printer 50.2 Fuser Error Make sure that you put the correct model fuser in the right printer. Hp Printer 50.1 Fuser Error Make usre your toner cartridge is fully seated and the top cover is firmly closed.

Load paper in the empty tray to clear the message. get redirected here Verify that the correct voltage fuser is installed in the product. 4. You can buy them for about $20-25 cash. No action required. Hp 4700 Printer 50.1 Fuser Error

If you are are getting a "50 fuser error" and have tried everything else, replace the low-voltage power supply. If loading media into the MP tray, select the size in the control panel menu. If the error continues, call your dealer or HP service representative. 51 PRINTER ERROR, CYCLE POWER The printer detected a temporary error condition. navigate to this website Turn the printer off.

The low power supply is the easy one to get to on the bottom. 50 Fuser Error Hp Laserjet 3050 Replace the environmental thermistor. 4. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd.

That did it for me.

The solution was to replace the LOW-VOLTAGE Power Supply, not the high-voltage one. Bad fuser ass'y.4. CONTRIBUTE TO OUR LEGAL DEFENSE All unused funds will be donated to the Electronic Frontier Foundation (EFF). 50.0 Fuser Error Hp Laserjet P1108 Verify that the correct model fuser is installed in the device. 9.

There are typically two sensing elements, a thermal fuse to prevent catastrophic overheating, and a thermistor to provide feedback to the heating circuit and indicate when to turn the heating current Remove jammed paper (see "Clearing Paper Jams" in this chapter). Improperly seated fuser. 2. my review here Bad fuser ass'y3.

Values of X, Y, and ZZ are as follows: X = DIMM type 0 = ROM 1 = RAM Y = Device location 0 = internal memory (ROM or RAM) 1 I truly appreciate it. HP LaserJet Error Codes 50-59 Message on printer displayWhat it meansWhat to do 50.X FUSER ERROR A fuser error has occurred. 1. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 55.xx PRINTER ERROR alternates with CYCLE POWER

Verify that the fuser power cable at the back of the device is connected and the ECU is fully seated.3.Verify that the seven wire connection is firmly seated in connector J405 Insert a toner cartridge or make sure the cartridge is fully seated and the top cover is fully closed. Register a free account to unlock additional features at BleepingComputer.com Welcome to BleepingComputer, a free community where people like yourself come together to discuss and learn how to use their computers. Temporary error code. 3.

Discussion topics include laser and inkjet printers, external hard drives, Webcams, monitors, keyboards, and mouse questions.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators Resolved Question Laserjet 5N "Fuser Erro: Cycle Power" Message by charmedlife417 / HP LASER PRINTER 9000, 9040, 9050MFP THIS IS FOR ALL ERROR 50.X 1. If on a surge protector plug straight in two the wall.3. This series of printers are legendary in quality and durability.

RESETTING ALL I/O This message is displayed during an All I/O Reset. Component parts are not readily available and fuser repair can become involved. That's it. controller.HP LASER PRINTER 1100, 2100, 4000, 40501.

If after replacing the formatter, the error persists, replace the ECU. Plug the printer into a wall outlet and see if this resolves the problem. 3. Since I have another working printer of the same model, I'll just swap the part and see what happens. Don't pay more cuz it's ancient technology.

Question about Canon Printers & Copiers 2 Answers Canon Ir2318 error code 00003 ...fuser for open thermistor,broken element . Verify that the correct model of fuser is installed. 4.