Home > Fuser Error > 502 Fuser Error

502 Fuser Error

Contents

After checking the Internet I determined it might have broken the ceramic heating element. Turn off the product, wait at least 25 minutes, and then turn on the product. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c03304304#N10143 Apr 20, 2016 | HP Printers & Copiers 2 Answers How do I fix a grey band on the right side of the page on an HP Pro 400 color Printers should be plugged directly into a wall outlet, not into an extension cable and certainly not into a UPS. navigate to this website

If you have another 4200 fuser even if the teflon is bad just try anyway to see if the message goes away. - dmzcompute Am still having the same error,so what Recommended action Close the door. and may not be used without advance written permission of PrinterTechs.com, Inc. fixyourownprinter forum stuff directly relevant to "50.2" on the LJ-4200 but with some relevance mindmachine article I'm working to improve. original site

50.2 Fuser Error P4015

I'll post results in a couple days when the new fuser unit (#3) arrives. Check to make sure there is nothing wrong with the connector; possibly damaged? A few weeks ago I had a massive paper jam in the fuser and a day later got a Fuser Error 50.1.

Reconnected the fan and re attached the covers. Recommended action Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew 50.1 Fuser Error and plugging directly into the 220v wall socket everything worked fine.

Power for the fuser is actually switched by the power supply board, largely under instruction from the DC controller. 50.2 Fuser Error Laserjet Pro 400 It is pressed down onto the heater by a spring. When first testing the printer, it was plugged directly into a 220v socket. look at this site Readers might be surprised but in our own office we found a 2 volt drop between a wall-socket and the farmost extension with nothing but computers and monitors plugged in.

Black cartridge low Description The toner cartridge is nearing the end of its useful life. 50.2 Fuser Error 4250 I never just keep ordering the same part over and over again. If the printer has been moved from a cold to a hot room (or from a warm place to a cool one) then the environment thermistor will be wrong and the If you have connected the printer via a USB cable, make sure to uninstall the printer from the Printers control panel (in Windows - the location name varies with the version

50.2 Fuser Error Laserjet Pro 400

Once an HP toner cartridge has reached very low, HP's Premium Protection Warranty on that toner cartridge has ended. http://www.fortwayneprinterrepair.com/wordpress/2013/02/26/hp-printer-cp3525-50-2-fuser-error/ You should see two blue pads where your index finger and thumb (on both hands) should pinch together then pull the fuser out. 50.2 Fuser Error P4015 Recommended action Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. 50.2 Fuser Error Hp 4700 See links below for purchasing information.

The thermistor on the fuser feeds back the current temperature to the DC controller. useful reference The fuser is cold. Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! Web Research In 2013 I tried querying Google with P4015 "50.2 FUSER ERROR" in quotes; it gave About 70,400 results, suggesting this is a fairly popular topic. 50.2 Fuser Error P3015

If you believe you purchased an HP supply, go to www.hp.com/go/anticounterfeit . Plug the product directly into the wall socket. Plug the product directly into the wall socket. my review here Notify me of new posts by email.

There are three main things in the thermostatic feedback loop - fuser, DC-controller and power supply, but the environment sensor is apparently taken into account as well. 50.2 Fuser Error Hp 5100 Related posts:HP Color LaserJet CP3525 Printer 50.1 Fuser Error 50.8 Fuser Error In the HP Laserjet P3015 Printer 58.20 - 58.2 Printer Error - HP Laserjet 4200, 4250, 4300, 4350 Posted According to the Service Manual the printer temperature is measured using the environment sensor thermistor on the fan housing and the DC controller estimates how long the fuser should take to

Without the OEM, it could be a brand new remanufactured unit, although I have seen brand new OEM stuff fail out of the box.

Once you wait 20 minutes and it still gives you a 50 error you must replace the fuser. Action Turn the printer off. Invalid driver Press [OK] Description You are using an incorrect print driver. 50.2 Fuser Error Hp Laserjet 4050 I have found the problem, I just need to get the 110v instead of the 220v.

I just got it from company becuase it's giving 50.2 fuser error. If the error is intermittent, attempt to isolate the issue to something specific in your environment. I'm hoping it's just a manufacturing defect on the "new" fuser I ordered from before. http://rlegsoftware.com/fuser-error/50-8-error-fuser.php Actual cartridge life may vary.

Also make sure it's plugged straight into a wall outlet and not a power strip or battery backup  with other devices. Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete. by unknown on Mar 19, 2008 at 8:13am Add comment Please sign in to comment 0 Since we have no idea what you did before, we can't advise you. Unexpected size in tray Load Press [OK] Description The product has detected paper in the tray that does not match the configuration for the tray.

I replace a bad DC controller board in this particular printer about a year ago. Load tray 1 , Description No trays are configured for the paper type and size that the print job is requesting. The service manual indicated some ohms testing to be done on the problem fuser and all results came back showing all the correct readings. I am hoping some of my info may be of help to someone and if anyone has anyone ideas or thoughts on my comments, I would love to hear them.

Remove tray 2 so the printer thinks no tray is there. If you are using a surge protector, remove it. Recommended action Load the correct paper into Tray 1, or press OK to use paper in a different tray. I am not a tech, but I have been repairing my own cars, printing presses, computers, printers and anything else that breaks for over 35 years.

Plug the product directly into the wall socket. Start of content HP Support Center Product SupportSearch HP Support CenterDownload optionsDrivers & softwarePatch managementSoftware updates & licensingDiagnostic passwordsTop issues & solutionsTop issuesMost viewed solutionsTroubleshoot a problemAdvisories, bulletins & noticesManualsRepair & Recommended action Press the OK button to clear the message. Plug the product directly into the wall socket.

That was after registration, dc controller and ps replacement.