Home > Hp Laserjet > 49.2319 Service Error

49.2319 Service Error

Contents

Power up printer and see if it goes to ready. Description The paper that is loaded in the tray is longer or shorter than the size that is configured for the tray. Replace formatter PCA. 60, 61, 63 MEMORY ERROR IIISi/4Si Only: 1. Working... http://rlegsoftware.com/hp-laserjet/49-1-d03-service-error.php

Figure 19: Reinstalling the print cartridge and closing the top cover If a jam message persists, jammed paper is still jammed in the printer. top 56.1, 56.2 PRINTER ERROR To continue turn off then on Description Unknown input/output device installed. Copyright @ 2005-2008 oesell.com All rights reserved. 苏州办公耗材网 oeSell【欧亿赛】 版权所有 Email:[email protected] 苏ICP备11044237号 用专业的精神做专业的事情,助力中小企业的产品销售和品质服务,我们崇尚合作,欢迎厂商、媒体联系合作事宜。 本站部分文字、图片资料来自网络,版权归原作者所有. 如果侵害了您的权益 ,请您来信告知,我们将在审核后24小时内删除该资料! 苏州办公耗材群 QQ群:13622968

HP LaserJet Error Codes and Service errors Back For additional help Check DC Power Supply voltages or replace DC Power Supply. 3. http://www.fixyourownprinter.com/posts/38589

Hp Laserjet 4250 Error Codes

Sign in to report inappropriate content. Look for the jam in another location, contact HP, or contact an authorized service provider. CAUTION: Ensure that all jammed paper is removed before closing the cover or tray. Figure 51: Closing DIMM access door Set the bottom of the cover onto the printer.

Types of messages Status messages Status messages reflect the current state of the printer. If the above action does not solve the issue, contact HP or authorized service provider. Temporary printer error, check printer's configuration. 57 ERROR II, IIID Only: 1. 57-1 Error - Incompatible memory card in front slot. 2. 57-2 Error - Incompatible memory card in rear slot. Hp Laserjet 4200 Cartridge Installed Message If the error 66.12.03 persists, replace the stapler unit.

Loading... Figure 58: Loading paper Make sure that the stack is flat at all four corners and that the top of the stack is below the maximum-height indicators. Try printing a job from a different program. https://www.printertechs.com/printer-troubleshooting/hp-error-codes Remove the print cartridge and check the paper path for paper.

Figure 32: Inserting the duplexer Open and close the top cover to clear the jam message. Hp Laserjet 4200 And 4300 Series Printers Drivers If the above action does not solve the issue, contact HP or an authorized service provider. Print again, if the paper jams try printing straight out the back instead to the top output bin. Same as 42 error. 49 FIRMWARE ERROR Only for the laserjet 4100: Try printing a different file if error persists remove all dimms and EIO devices, last replace formatter. 50 ERROR

Hp Laserjet 4200 Error Codes

IIISi/4Si Only: 1. Figure 42: Plugging the power cord in Reinstall the optional duplexer, if it was removed. Hp Laserjet 4250 Error Codes III, IIID Only: 1. 53-1 Error in front memory slot. - Replace memory card. 2. 53-2 Error in rear memory slot. - Replace memory card. Hp Printer Error Codes List External fuser access door not closed. 4P/5P Only: 1.

DC Power Supply/Main motor driver malfunction. my review here NOTE: A loss of data will occur. If the above action does not solve the issue, contact HP or an authorized service provider. X=1: Beam detect malfunction. 2. Hp Laserjet 4250n 49.4c02 Service Error

top 68.X PERMANENT STORAGE ERROR For help press ? Reinstall all paper input trays. Front Door-open Sensor (PS402) broken or stuck. 2. click site Description A fuser error has occurred.

Pull outward on the blue staple cartridge to remove it. 13.98 Paper Jam Figure 46: Pulling the cover on the right side of the printer Remove the cover from the printer. Push the blue levers upward and pull the fuser straight out of the printer.

If the printer is plugged into a wall outlet, try another power source in the building that is independent of the one currently being used.

Turn the printer off and then turn the printer power on. If the above action does not solve the issue, reload the tray with the correct paper size. This is typically an e-label issue. 68.0 Permanent Storage Full Check front panel settings. 3.

Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4. If the message persists, contact HP Customer Support. Replace fuser. navigate to this website top CLEARABLE WARNINGS and AUTO CONTINUE settings Some printer messages are affected by the printer CLEARABLE WARNINGS and AUTO CONTINUE settings.

Description A stacker or stapler/stacker error has occurred. Check tansfer roller. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. DC Controller PCA malfunction. 4/4M/4+/4M+ Only: 1.

Remove any paper found. The issue can be caused by a firmware error, invalid print commands, corrupt data, invalid operations, poor quality parallel cables, poor connections or specific applications. If the above action does not solve the issue, contact HP, or contact an authorized service provider. If the message persists print a Configuration page and check the printer settings to determine which values have changed. (To print a Configuration page, open the Information menu at the printer

If the error message persists, contact HP support. Lift the optional duplexer up and then pull it out to remove it. Figure 43: Reinstalling duplexer Turn the printer power on. Check Drum Sensitivity microswitches.

If the problem persists see if it is a particular doucment or application casuing the issue and check with the vendor of the application. If you are printing from Tray 1, verify that the correct paper size is selected at the printer control panel. FONT COLOR="orange" size=4>4000/4050/4100/5000/8000/8100: 1. top 13.12.07 JAM IN STAPLER Description There is a jam in the stapler cartridge.

Open the trays, remove the paper, and remove the obstruction. Cycle power. 4.