Turn the printer off and then on. 3. A 5 mW laser can slowly damage your eyes and eventually cause blindness without you even knowing it – don’t play with the laser.” To contact Steve Geishirt, call (800) It might be necessary to use a small flat-blade screwdriver to release the tab inside that small hole. Hold the output assembly in place (located at the top toward the rear A loss of beam detect occurred. 2. my review here
This printer is being used primarily for a non-profit organization. Left cover 1. It will need to be replaced.
Disconnect the toner cartridge drive arm by using needle-nose pliers to squeeze the pin and push it back through its retaining hole on the top cover. See picture below. The book does list a 41 error but not as a “printer error.” Suggested parts replacement focuses around the laser scanner, cables, and engine controller so it appears 41 still means Turn the power off and wait 30 seconds and turn the power back on. 3. Hp Laserjet P3015 Laser Scanner Assembly Release one tab. 7. Rotate the bottom of the rear-door assembly away from the product. 8.
Replace the scanner cables to D.C controller. 3. 51.10 Error Replace the laser scanner ass'y HP LASER PRINTER 9000, 9040, 9050MFP 1. Karri says: August 6, 2016 at 9:42 pmNo obstante, el tratamiento fue llamado de este modo por obtener resultados parecidos al procedimiento estético facial. http://www.imagesourcemag.com/ism-article/511-errors-4100-printers If a surge protector is being used, remove it and plug the printer directly into the wall. 4.
Most of the customers we are talking to indicate the laser scanner has been the fix for their printers. Hp Laserjet 4100 Error Codes Press the SELECT button to continue or press ? The printer has experience an internal hardware error. 2. Replace the laser scanner assembly. 4.
Hopefully, this problem on the P3015 is a few isolated instances and will not be an ongoing issue. http://fixyourownprinter.com/posts/73895 Reply With Quote Quick Navigation Hewlett Packard Laserjets Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Printer Forums Hewlett Packard Laserjets All Other Laser Printers 51.1 Printer Error Hp 4100 If you have found the information useful and possibly saved you a service call, a donation would go a long way in keeping the articles coming and help my family understand 41.2 Printer Error Lift the laser/scanner up and out of the product.HP LaserJet Enterprise P3015 Series Laser/Scanner Assembly, LJ P3015/M525mfp RM1-6322-000Conclusion about the 51.10 error in the HP laserjet P3015 PrinterHopefully the 51.10 error
foot scrubs scrape says: April 15, 2016 at 6:45 pmMy partner and I absolutely love your blog and find most of your post's to be precisely what I'm looking for. http://rlegsoftware.com/printer-error/51-2c-printer-error.php controller3. But when an error occurs in your printer you won’t be able to continue your printing process. From the DIAGNOSTICS menu, run the laser/scanner motor component test. 51.10 Error P3015
Typically when a 51 error occurs, the print on the delivered page - if it delivers - is either distorted, prints a completely black page, or there is no print whatsoever. Showing results for Search instead for Do you mean or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Home | Error Codes | Hp Printers | Toner Cartridges | Hp Printer Accessories | Hp Plotters Copyright © 2011 Advanced Laser Services, Inc. http://rlegsoftware.com/printer-error/59-90-printer-error.php Fold down the rear output bin at the back of the printer, and remove 2 screws (see picture, screws circled as #1) hidden underneath the lip of the top rear of
Turn the printer off and turn it on again. 3. Hp Laserjet P3015 Laser Scanner Assembly Replacement by unknown on May 23, 2012 at 1:06pm Add comment Please sign in to comment 0 The laser scanner unit on top of the printer. Amazon, the Amazon logo, Endless, and the Endless logo are trademarks of Amazon.com, Inc.
This is the feedback system that initially helps synchronize the laser beam and keep it synchronized. Looking at the possibility that only one of the laser beams fail, this could explain why print on the page looks fine and the 51.1 error occurs. Then remove the screw that holds the grounding cable in place, circled as callout 2 in picture below. Finally remove the 4 recessed screws (un-numbered circled in picture below) located around Rm1-5465 Turn the MFP off and then on. 2.
In all of the cases reported here, when the 51.1 error occurred, the print looked fine on the page. This area detects the beam and turns it back into an electrical pulse that the engine controller uses to synchronize the laser beam as described before. Please check out my web site as well and tell me how you feel. http://rlegsoftware.com/printer-error/51-2-m-printer-error.php The printer's log says it's 51.1.0 or 52.1.0, but all it says is to powercycle the printer.The printer would start the job, load a paper, and throws the error message.
Replace the ECU. See picture below. Unplug the 3 connectors circled as callout #1 in the picture below. First Time Here? Engine Controller The third possibility here is the engine controller, which keeps track of the synchronization process by sending laser pulses to the beam detect mirror, which then sends them to
I will look into that!Could you possibly point out in the picture at http://computer.howstuffworks.com/laser-printer2.htm which part I'd be looking for?BTW, if my girlfriend prints via my PC (printer shared via both Articles Forum New Posts FAQ Calendar Community Groups Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Blogs Advanced Search Forum Printer Forums Hewlett Packard Laserjets Defective DC controller. 4. Check the cabling connections to the laser/scanner assembly. 5.
Printers are the devices which take information from your computer and then transfer the data to paper. Make sure that the door is completely open. 2. Disconnect one connector, and then remove one screw. 3. Slide the control panel toward the front of the product to release it.