Home > Printer Error > 51.2 C Printer Error

51.2 C Printer Error

Contents

top 13.02.00 JAM IN TRAY X For help press ? Personally, I support 230 endpoints. Clean the pick-up roller and separation pad and replace if worn. The printer will perform a cold reset and then continue its power-on sequence. my review here

Open the top cover. mr.printer is online now hp lj5500 error message 51.2c. Release the check button when the Ready, Data, and Attention light are on steady. Release the check button when the Ready, Data, and Attention light are on steady. http://www.printertechs.com/printer-troubleshooting/346-51-2c-51-m-51-2y-51-2k-error-on-hp-color-laserjet-4600

51.2y Error 4600

Freshfield, Liverpool, UK < Previous | Next > Wonderful service, prompt, efficient, and accurate. Press (Up Arrow) until NVRAM INIT is highlighted. See Figure 2. Replace cable ***'y from scanner to D.C.

or it's affiliates. LaserJet 4600 Printer Manual LaserJet 4600... When the memory starts counting, press and hold the green (Select) button. Rg5-6380 Help this question get an answer by entering the correct category or product below.

Action For step by step information, press the green (Select) button to continue. top 54.1 PRINTER ERROR Description A low fuser temperature error has occurred. Press (Down Arrow) button once. https://www.printertechs.com/shop/laser-scanner-assembly-for-hp-color-laserjet-4600-series-rg5-6390 Perform a cold reset on the printer.

top 54.5 PRINTER ERROR Description There is a problem with the Color Plane Registration Sensor. Laser Scanner Assembly For Hp Color Laserjet 4600 Series Press (Down Arrow) button once. Continue holding the green (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. Action Turn the printer off, and turn it on again.

51.2k Printer Error 5500

The control panel will display SELECT LANGUAGE . http://www.fixyourownprinter.com/posts/60543 The control panel will display COLD RESET . 51.2y Error 4600 Mary C. Hp 4600 Laser Scanner Assembly Turn on the printer.

When the memory starts counting, press and hold the (Select) button. http://rlegsoftware.com/printer-error/51-2c-printer-error.php Press (Down Arrow) button once. If the error persists, perform an NVRAM initialization. If no paper is found, re-adjust all paper guides in trays to ensure settings are correct. 51.2y Printer Error 5500

Description Non-HP magenta print cartridge installed. Lift the fuser by grasping the fuser housing above the green arrow on the left and right. Reinstall the fuser. http://rlegsoftware.com/printer-error/59-90-printer-error.php Press (Down Arrow) button once.

Firmly press down on the two green handles on either side of the fuser to re-engage the fuser rollers. Rg5-6390 need to get to the menu to 9/29/2016 9/29/2016 Richard It will not print. The control panel will display COLD RESET .

top 68.1 PERMANENT STORAGE WRITE FAIL TO CONTINUE PRESS Description The flash DIMM or hard disk storage device is failing to write.

top 54.18 PRINTER ERROR Description There is a problem with the Black CPR sensor. IN THIS DISCUSSION HP 356892 Followers Follow Join the Community! Action Turn the printer off, and turn it on again. Hp 5500 Laser Scanner Assembly Action Turn the printer off, and turn it on again.

If using DDR SDRAM for the HP Color LaserJet 4650, make sure it meets specifications and is correctly seated. When the memory starts counting, press and hold the green (Select) button. Release the check button when the Ready, Data, and Attention light are on steady. http://rlegsoftware.com/printer-error/51-2-m-printer-error.php Pull paper by bother corners to remove it.

Some parallel cables might be missing pin connections, might be bent or broken, or might otherwise not conform to the IEEE-1284 specification. Continue holding the green (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. Posted on Jul 09, 2009 Helpful 1 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great Pull open the Electrostatic Transport Belt (ETB).

Try a different electrical circuit or outlet. errors in the 51 range are laser scanner errors, it's saying either the laser is out or the scanner motor is not turning, or not turning fast enough. Rating is available when the video has been rented. Turn on the printer.

Perform a cold reset. When the memory starts counting, press and hold the green (Select) button. Press (Down Arrow) button once. If this message persists, contact an HP-authorized service or support provider.

If a critical error persists, service is required. The control panel will display COLD RESET . Before I got the chance to study it more carefully, one of our help desk techs wiped her machine. Turn the printer off, and turn it on again.

alternates with TO CONTINUE PRESS Description An NVRAM storage device is full. When the display begins showing the memory count, press and hold (Down Arrow) until all three lights on the control panel are lit. If this message persists, contact an HP-authorized service or support provider. I advise you to call a tech out to take a look at it rather than trying to fix this on your own.If it isn't happening too often I'd probably just

Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. An improper network protocol might be in use.