Home > Printer Error > 57.1 Printer Error Cycle Power To Continue

57.1 Printer Error Cycle Power To Continue

Contents

Replace DC Controller PCA. 3. Bad laser unit or improper laser power setting. 2. The line voltage and current source at the printer location might need to be inspected to ensure that they meet the electrical specifications for the printer. Back Error 11 - Paper Out Paper tray empty or not seated correctly. my review here

PCL file being sent to printer while in PostScript mode. 2. Paper pickup clutch turning more than once? Note II: Short C211 on the DC Controller to bypass Error 50 time delay. (The printer must be turned off.) Note IID: Short C216 on the DC Controller to bypass error Turn the product power on. weblink

Rh7-1552

Respond to this 0 You have a motor start error. Watch the termination's on the network cabling. [email protected] Posted on Dec 26, 2007 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Anonymous SOURCE: HP psc 1350 HP You may need additional memory. 4L Same thing with to much data or the page is to complex.

Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4. Check these items. Reseat connector J201 on Sensor PCA. 3. The motor works, and works quiet, its not it!3.

The MIO card is defective or maybe just not seated correctly. 52.0 Printer Error Cycle Power To Continue Hp 5100 Check tansfer roller. On the II and III Series printers, this error message can be caused by a faulty paper control PCA. Replace Formatter PCA. 3.

Back back to top How did we do? This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2. The printer door/lid is open. 2. please help & say what should I do exactly ????

52.0 Printer Error Cycle Power To Continue Hp 5100

At least one of two tabs must be present. X = Description 4 Printer Fan 7 Duplex Fan 1. Rh7-1552 A broken tooth on one gear is all it takes. Rh7-5294-000cn ERROR 80 80X.YYYY ALL Printers The EIO card in slot X has encountered a critical error -power cycle, reseat card then replace card if needed.

Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the http://rlegsoftware.com/printer-error/64-printer-error-cycle-power.php View Most Popular Printers & Copiers Related Question 57.01 error Printers & Copiers Open Questions: 0 Answers hp deskjet 1515 all light blink Sep 29, 2016 | HP DeskJet Printers & There's still a squeak, but not from the motor, a little higher from the Delivery Unit.5. Also on the 4V/4MV check the door open sensor (PS402) on the terminal board located under the transfer roller.

Reseat connections to the specified fan and DC controller. Power Supply (P/N RG1-0906- 000). Taking out the Fuser and changing from Letter to paper mode (pushing down the 2 levers), and inserting the fuser back started with some abnormal grinding noise. get redirected here Check I/O Cable, it could be the wrong cable or damaged.

Paper Control PCA malfunction. 4V/4MV Only: 1. See "Cooling fan (right side; HP LaserJet 4300 series printer only)" on page 170. 3. IIISi/4Si Only: 1.

It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

Michelle is online now Hp Laserjet 5100 getting error message 57.1 printer error. Back back to top How did we do? Couldn't have asked for more. Check connectors J204 and J6 on DC Controller and conenctor at Fan 1. 2.

Thank you for the speedy shipment and response. Power down the printer and remove the duplexer. Justanswer.com. useful reference Replace formatter PCA. 4000/4050/4100/5000/8000/8100 Only: 1.

Error 55 On IIISi/4Si Printers this is due to the DC controller not receiving the proper information upon startup. Replace the engine. Generally you will need to replace the laser scanner and ocassionaly the DC controller PCA Back back to top How did we do? Computer and printer may be set to different baud rates. 2.