Home > Printer Error > 59.90 Error

59.90 Error

Contents

If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used. 4. Open the top cover and remove the toner cartridge. 2. by unknown on Nov 9, 2006 at 3:43pm Add comment Please sign in to comment 0 The ETB test is to determine if the motor is running.The fact that it started sensor9 cyan drum home position sensor10 black drum home position sensor11 black density sensor12 cyan density sensor13 magenta density sensor14 yellow density sensor19 ETB speed control sensor20 color plane registration sensor21-24

Any help would be much appreciated. Release the green button and arrow down once to "Cold Reset" and hit the green button again. Pressing the button should clear the message. Turn the printer off, wait 10 minutes, and then turn the printer on. 2. check my blog

59.90 Printer Error Hp 5550

by Rob S on Apr 23, 2004 at 8:49am Add comment Please sign in to comment 0 I am not in front of the machine so this is from memory. You can't post answers that contain an email address. and may not be used without advance written permission of PrinterTechs.com, Inc.

A problem exists with the DIMM in DIMM slot 3.55.x Engine communication errorThe Attention light is on.57.x Fan motor errorThe Attention light is blinking.64 Scan buffer errorThe Go light is blinking. Sign Up Login Add Question unknown asked Apr 22, 2004 at 6:56am 0 HP Color LaserJet 4600DN HP 4600dn This printer is giving us an error 59.90 when you turn it The magenta cartridge and the yellow cartridge do not close completely when I pull the ETB down. Call us 608-831-2396 for more information.  New to our website?

Respond to this 0 ETB motor error1 Clean the ETB unit intermediate connector, J4017.2 Reconnect the connectors J4022 for the ETB motor, J4017 between the ETB and the printer, and J4014 Etb Motor Immediately press and HOLD the green button until the memory test completes and the 3 lights are all on (lit).3. it should now show on, use the right arrow once to change it to off and hit enter 2 times let the printer reboot and its should be fixed Posted on https://www.orionmarket.com/product_error/7513/HP/HP-3800/59.90-error/ One of your cooling fans has probably ceased to function, the fan will most likely need to be replaced.

Verify the environmental thermistor cable is securely connected. 3. by unknown on Apr 22, 2004 at 9:02am Add comment Please sign in to comment 0 Anyone? The printer was not my default printer at the time of printing.I then looked at the display on the printer and it is stating Printer Error 59.90. Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum!

Etb Motor

The page containing the error will automatically be reprinted. 2. Someone told me it's a motor error, but Moe says that motor problems with this model are almost unheard of. 59.90 Printer Error Hp 5550 Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3. 59 C0 Printer Error Reply 0 Re: Printer Color Laser Jet 4650 Error 59.90 01-12-2016 02:34 PM Thank you!

Respond to this 0 How old is your printer? Check the main motor’s cable to ensure that it is seated properly. 4. On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer Accessories Error Codes Our technicians can help you Probably the ETB motor. 0 LVL 6 Overall: Level 6 Printers and Scanners 3 Message Assisted Solution by:Panjandrum2004-11-19 These are the IDs for 59.x error codes on the HP4600 0

Calibrate the printer after replacing the DC controller. 0 Write Comment First Name Please enter a first name Last Name Please enter a last name Email We will never share this Check the power at the customer’s location. 2. If the connector is damaged, replace it. All rights reserved.

If that does not work, replace the fuser. Printingcan continue, but there may be unexpected behavior.X Description0 onboard NVRAM1 removable disk (flash or hard)79.XXXX PRINTER ERRORA critical hardware error has occurred.8X.YYYY EIO ERRORThe EIO accessory card in slot X The problem could be caused by a timing error or an intermittent connection.X — Description00 — Communication error01 — DC Controller memory error02 — Outgoing parity error03 — No engine response04

Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!!

Featured Post How your wiki can always stay up-to-date Promoted by Quip, Inc Quip doubles as a “living” wiki and a project management tool that evolves with your organization. Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts Check the fan’s connector and make sure the fan is not blocked. 2. Connect with top rated Experts 18 Experts available now in Live!

Turn the printer off, and reseat or replace the specified DIMM. 2. Ask Loading...Oops :Please try again. Printer Repair in Salt Lake City, Utah, YP.* 5211 South Green Pine Drive Murray, UT 84123 * USA *Office:(801)506.0277 *Copyright© Office Imaging Systems 2004, All rights reserved. Our quality is highly regarded due to our constant testing and attention to detail.We sell a wide variety of maintenance kits and parts, meticulously refurbished printers, and high-quality toner cartridges.

Turn the printer off and then on. 3. Comment Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product? On rare occasions, the formatter is at fault, which is usually indicated by a 79 Service Error.50.X FUSER ERRORX Description1 low fuser temperature2 fuser warm-up service3 high fuser temperature4 faulty fuser5 It's about 18 months old.

Good luck. We don't sell hard drives, monitors, software, mp3 players, or the zillions of other computer products sold by every other cookie-cutter website. It took pushing the grren key several times, but finally it went into check mode and promptly ask me to insert the cartridges. Measure the resistance between the fuser connectors.

In some cases, electrical noise in the cable can corrupt data during transmission to the printer.