Home > Printer Error > 60.2 Printer Error

60.2 Printer Error

Contents

I foundthis The symptoms you described were sketchy. Replace the D.C. Placing the guides too tightly against the paper can cause the paper to rise slightly. It has 3 ribs on the right side of the tray rails to eliminate this problem. http://rlegsoftware.com/printer-error/59-90-printer-error.php

Profitable Desktop Color Printing: Yes, It Is Possible Success Spotlight: Compugen Tech Talk: Having Trouble Clearing Error 60.2 On Your HP LaserJet 42xx/43xx? Preview post Submit post Cancel post You are reporting the following post: My Hp 4200 Laser printer gives me 60.2 error This post has been flagged and will be reviewed by Tray 3 lift motor error has occurred.2. You should be able to hear the paper stack being lifted. http://www.partsnow.com/news/ImagingNow/vol2iss1/clearing-error60-2_onhp

Lifter Motor Error

You must replace the paper tray if you find damage or excessive wear. If the problem persists, contact a service professional. See Tray 2 lifter-drive assembly. 5 Replace the dc controller PCA. It doesn't receive tray.

The specific tray has experienced an error while lifting the media. 2. Normally, when the printer is powered on, it will run the lift motor to raise the stack to the pick roller; if the motor fails or if the tray doesn’t lift You’re Not The Only One… After powering on your HP LaserJet 42xx/43xx, you get Error 60.2 displayed on the control panel. 60.3 Printer Error Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc.

Flag Permalink Reply This was helpful (0) Back to Peripherals forum 6 total posts Popular Forums icon Computer Help 51,912 discussions icon Computer Newbies 10,498 discussions icon Laptops 20,411 discussions icon 60.2 Hp Printer Error controller. If it slides back and forth check the motor mount. http://www.copytechnet.com/forums/hp/27131-my-hp-4200-laser-printer-gives-me-60-2-error.html When the tray is full, the weight of the paper on the tray can damage the gears and cause them to start skipping, which is the clicking/clunking noise.

by dmzcompute on Jun 23, 2009 at 7:43pm Add comment Please sign in to comment Please sign in to comment Unknown Printer Buy discount ink Buy this printer © Copyright 2011-2016, Hp 4200 Tray 2 Lift Motor by dmzcompute on May 10, 2006 at 12:14pm Add comment Please sign in to comment 0 If I ever find a problem I haven't seen before, I always check this forum In this case the paper indicator in the front of the tray will be in the full position. Then hold down the check mark button while powering on the printer and waiting until all three lights come on solid at the same time.

60.2 Hp Printer Error

Most common cause of this issue is a little spring which runs from the outside of the motor to a clip on the frame has broken or come off. https://www.cnet.com/forums/discussions/my-hp-4200-laser-printer-gives-me-60-2-error-367846/ Just make sure you have your model number makes it a lil easier. Lifter Motor Error The part numbers are: WG8-5362-000 (HP 4200/4300) WG8-5624-000 (HP 4250/4350) If this does not take care of the problem, you will be looking at replacing the DC Controller. 60.02 Printer Error You’re Not The Only One… Tech Talk: Having Trouble Clearing Error 60.2 On Your HP LaserJet 42xx/43xx?

Perhaps none are needed at all. this page Make sure that the tray lift sensor flag is functioning correctly. Tips & Warnings Use caution when handling the paper tray. If you give me an information about my broken piece, I will buy a spare part on this website. 60.2 Printer Error Hp 4200

by dmzcompute on Nov 3, 2006 at 3:56pm Add comment Please sign in to comment 0 When you print a configuration page it will list what size and type of paper You can also open the shutter on the toner cartridge and see the image on the drum.If you are using refilled cartridges it's not unusual to have more than one bad Check tray for obstruction. http://rlegsoftware.com/printer-error/51-2-m-printer-error.php Loud banging sound occurs when tray is installed, followed by the paper indicator moving to the full position regardless of amount of paper in the tray.

Its 50 cents from HP. Rm1-1074 Email me with the link above if you want a pdf page which will show the spring. Good Luck and thanks for your service to our country.

Sometimes, however, simply removing loose paper from the tray resolves the problem.

Removed the paper tray and found the letter size paper all the way back to where the legal stop is. is there any manuals I can get to help guide me on how to take the side panels off, man give me a laser jet 4 plus any day......hahaha thanks, and You can also watch the paper level indicator on the front of the tray to see if it moves. 4. Parts are thoroughly tested, inspected for damage & defects and guaranteed 100% fully functional. $29.00 Call for Assistance 877-755-5300 Home About Us Contact Us Search Site Map Printers Supplies Accessories Parts

Remove the toner cartridge, you can now see an unfused image on the paper, if it looks good here then the problem is probably the fuser, if it looks bad here About eHow Advertise Write For eHow Contact Us Connect with us Terms of Use Report Copyright Ad Choices en-US Privacy Policy Mobile Privacy demandmedia.com © 1999-2016 Demand Media, Inc. by Stephen on Jul 2, 2004 at 6:28pm Add comment Please sign in to comment 0 If you are talking about the fuser assembly which binds the toner to the paper http://rlegsoftware.com/printer-error/51-2c-printer-error.php DiscoverC Home Decor & Repair Crafts Food & Drink Garden Entertaining Fashion & Beauty Holidays Tech Personal Finance Cars Pets Legal Honest Hacks FOLLOW US    U Search U

by unknown on Aug 30, 2005 at 7:45pm Add comment Please sign in to comment 0 There are 3 service notes for the 4200:01: Introductury note that described the printer. Alternatively, try swapping the paper trays if your printer is equipped with multiple trays. Lift drive assembly will have to be removed to perform this repair. HP LASER PRINTERS 3SI, 4SI, 4V 1.

Have a nice day. Model...