Home > Printer Error > 64 Printer Error Cycle Power

64 Printer Error Cycle Power

Contents

Maladjusted or bent Switchback assembly. Remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM in the lowest DIMM slot.) 7. Wait until ... Cycle power to printer Bad formatter PCB LJ4, 4+, 4P NVRAM not initialized. 68 Memory IIISi, 4Si, 4V Bad SIMM memory. http://rlegsoftware.com/printer-error/57-1-printer-error-cycle-power-to-continue.php

Press the Continue key and the printer will repeat the page. Press GO to clear the error message and continue printing. 2. XX Description 00 memory error on the cartridge or 01 memory device not found YY Description 00 black print cartridge 1. Tab missing on top cover. Homepage

57.1 Printer Error Cycle Power To Continue

Replace the formatter. 79 & 80 errors - general info. Try the DIMM in another slot. (The firmware DIMM must remain in slot 4—the lowest DIMM slot.) 3. That's why we've put together this on-line shop of printer parts.

DC Controller PCA malfunction.
12 OPEN or NO TONER or NO EP IIP/IIP+/IIIP Only: 1. Figure 18: Closing the finisher cover Move the finisher away from the product (Figure 19). If the printer picks two sheets of paper at once. 4. Hp Printer Error 79 remove the page from the output bin and press [Go].

Replace Paper Control PCA (Solenoid/Sensor PCB Assembly). 4. Samsung Printer System Error Cycle Power Figure 43: Opening the stapler unit door Slide the stapler-unit away from the printer. (Figure 44). The previous page is reprinted automatically. 2. http://www.mj-printers.com/repair/hpcodes.html Figure 15: Pushing the device back into place top To clear jams in the multifunction finisher Open the finisher cover (Figure 16).

Replace the toner cartridge and retest the printer. 49.XX PRINTER ERROR A firmware error occurred. 1. Hp Printer Error Codes Replace a DIMM or EIO device if you determine that it causes the error. 11. If the error continues, call your dealer or HP service representative. 65 PRINTER ERROR, CYCLE POWER The printer identified a RAM controller error. IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si

Samsung Printer System Error Cycle Power

Clear any pending print jobs. Ensure that paper trays are loaded and adjusted properly so media can feed from the tray. 57.1 Printer Error Cycle Power To Continue Cycle power to printer Bad formatter PCB LJ4, 4+, 4P NVRAM not initialized. 52.0 Scanner Error Hp Laserjet P1007 Print a configuration page and check the printer settings to determine which values have changed. 68.X PERMANENT STORAGE FULL The printer's permanent storage is full.

Loading Envelopes into the Optional Envelope Feeder Lift up the pressure plate (A). Get More Info top Possible printer jam locations Figure 3: Jam locations 1 - Bin 1 2 - Front door and print cartridge area 3 - Bin 2 4 - Output device 5 - We know that you don't want to spend hours trying to figure out a printer problem. Figure 37: Removing the staple cartridge Pull the cartridge lever up (see Figure 38). Hp Printer Error Code List Pdf

If a message persists after performing all of the recommended actions, contact an authorized HP Service or Support Provider: Click here for information on contacting HP Customer Care. Computer is powered off Unseated or defective MIO card 5P Indicates an abnormal connection break occurred while transferring data from the computer 41 Error (Temporary print engine failure) All printers Reset Recommended action Touch Continue to print the transferred data. (Some data might be lost.) If a message persists after performing all of the recommended actions, contact an authorized HP Service or useful reference top To clear a staple jam from the multifunction finisher Open the stapler-unit door (Figure 43).

Paper pickup clutch turning more than once? Hp Warranty Check If YES then ... Verify that the fuser is properly installed. 13.5 PAPER JAM CHECK REAR DOOR Paper-delay jam at fuser. 1.

PS402 on front door PCA under transfer roller Bad DC controller PCB 16 Toner low All printers Toner uneven in cartridge Bad toner cartridge contact points Replace high voltage power supply.

From the configuration page, determine the number of pages since the last maintenance. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device. Display the event log Select Display Event Log to scroll through the contents of the event log from the control panel. Hp Support Turn the product off, and then turn the product back on.

Figure 51: Reinstalling the staple cartridge Slide the stapler unit into the finisher (Figure 52). top To clear a staple jam from the optional stapler/stacker Move the stapler/stacker away from the printer (see Figure 35). If the error reappears, call your dealer or HP service representative. 79 SERVICE (XXXX) The firmware has detected an unrecoverable error. this page Browse Categories Answer Questions HP LaserJet 4050n Printer HP LaserJet Printer and Copier HP Printer and Copier Printers & Copiers All Unanswered Join Sign In Ask a Question × HomeForumPrinters &

Check the light guide and clean it if necessary. Execute a form feed from the computer or the printer control panel. top 51.x PRINTER ERROR alternates with TO CONTINUE CYCLE POWER Explanation A temporary printing error occurred. top 60.x PRINTER ERROR Explanation An obstruction prevents the tray specified by xx from lifting paper properly for feeding.

Remove same 72 Service All printers FONT cartridge removed during formatter access. Remove RAM expansion card. If this error appears, switch the printer off for at least 15 mintues and then back on. The chip may be missing or defective or contain incorrect information.

Replace the specified DIMM 64 PRINTER ERROR alternates with CYCLE POWER A scan buffer error occurred 1. Replace toner cartridge. 2. Temporary printer error, check printer's configuration. 57 ERROR II, IIID Only: 1. 57-1 Error - Incompatible memory card in front slot. 2. 57-2 Error - Incompatible memory card in rear slot. External fuser access door not closed. 4P/5P Only: 1.

Short C202 on the DC controller PCB to bypass the 20 minute delay, power printer OFF!!) 4V, 4L, 4P, 5P Verify fuser is properly seated Replace fuser 51 Error (Loss of Try using media that is known to be good. DC Controller PCA malfunction. 4/4M/4+/4M+ Only: 1. Replace memory PCB 53-2 - Error in rear memory slot.

Remove all media in the paper path, and then open and close the top cover. 2. Also verify the entire paper path is clear to prevent a recurring paper jam error message. Replace cable, fuser to DC Controller (P/N RG1-0907-000) II, IID, III, IIID Only: 1.