Home > Socket Error > 10061 Cute Error Ftp Socket

10061 Cute Error Ftp Socket


Right-click on this link: http://www.coaa.co.uk/WMM.COF and select Save link as (or whatever your browser uses). Why don't most major game engines use gifs for animated textures? it cannot retrieve a directory listing or files.In certain firewall configurations, users may encounter Connection Refused errors (#10061) when using SyncBackSE/Pro to establish a connection to a remote site. Left by Cliff Cummings on May 15, 2010 9:05 AM # re: FTP error 425, "Can't open data connection." Try stopping VPN services, es "Cisco VPN Inc." if any is installed. http://rlegsoftware.com/socket-error/500-socket-error-10061.php

Why WinScp connects to one account but give an error message when I try to connect to second account on the same Host????? Use Task Manager to kill and PlanePlotter.exe processes. Left by Reza Safe on May 02, 2012 5:48 AM # re: FTP error 425, "Can't open data connection." STOP CISCO VPN Services. This could happen if you are trying to run more than one instance of Plane Plotter - perhaps the previous shut-down of Plane Plotter wasn't correct, and the old instance hasn't see this

Ftp Socket Error 10061 Connection Refused

I'm no longer seeing shared aircraft Ensure that the sharing button on the toolbar shows: either two arrows with no red line , one downwards arrow but not one upwards To see if this is the issue for you, run the following PowerShell command: @("AppFabricCachingService","RemoteRegistry") | % { get-service $_ } If either of these two services are stopped, then you OR read more like this:Change vsftpd FTP Server Port Number 21CentOS / Red Hat Linux Install VSFTPD FTP ServerUbuntu Linux vsftpd ftp service / server install, configuration howtoCentOS / RHEL IPv6 Are some defaults different in comparison to other Windows versions? –Wolf Sep 28 '15 at 9:29 add a comment| up vote 3 down vote I had the same problem.

This parameter is often configurable if you control the server, and is likely read from some settings file or the registry. You may also want to be sure you are using a passive connection. Thanks a lot. Socket Error 10061 Outlook Express When will be released the next version ?

I think we can discard this possibility as too much of a long shot though, since the router has 64K simultaneous connections to the same destination address/port before exhaustion. Ftp Error Code 10061 Turns out it was set that way by the previous owner in the area you specified. WSAECONNREFUSED (10061) 10061 is a Connection Refused error sent to you by the server. http://www.networkautomation.com/urc/knowledgebase/common-ftp-socket-errors/02899795-9874-19FA-89D9FA88304286FA/ Left by Kitchen Appliances on Apr 12, 2012 11:59 AM # re: FTP error 425, "Can't open data connection." Command: LISTResponse: 425 Can't open data connection.Error: Failed to retrieve directory listingfirewall

Go to: Options, Sharing, Setup and uncheck "Enable FLARM targets" NGDC Warning Some users are getting a pop-up message when starting Plane Plotter about some magnetic data being out Socket Error 10061 Connection Refused Smtp The Share button is greyed out You need to follow the registration procedure to "un-grey" the share button and then you will need to authenticate the installation to gain access QNH doesn't work but normal sharing does Please note that QNH uses FTP to retrieve the data, rather than HTTP which is used for normal sharing. The document here states on page 6: "TIS-B: This system is a new traffic broadcast information service on 1090MHz (and UAT) in USA.

Ftp Error Code 10061

Investigate how to configure your server. http://planeplotter.pbworks.com/Common-error-messages Locate your Plane Plotter directory (where PlanePlotter.exe lives) and copy the file you have downloaded to that directory. Ftp Socket Error 10061 Connection Refused Less frequent are Mlat position estimates (white), ACARS position reports (red, blue or green - see Help file for details) and HFDL reports (cyan - which you described as light blue). Socket Error 10061 Windows Live Mail prikryl wrote: peter31 wrote: Now...

In my case the fix was to turn off the FTP virus scanner on my Endian firewall, then everything suddenly worked. navigate here Either one may be blocking the ports needed to make a successful FTP connection to the server. NTP is easily downloaded and installed, runs without attention, and of course, it's free. When a NO REG aircraft plot appears on a Plane Plotter chart or map, Left Click on the black Aircraft List icon at the top left of the screen (Fifth icon Socket Error 10061 Connection Is Forcefully Rejected (server)

Socket Error # 11004, Unable to connect: Check to make sure there isn't a trailing or leading space character on the FTP hostname. Well that's difficult question. Please post a full log file showing the problem. http://rlegsoftware.com/socket-error/10061-error-socket.php Then click on Start button.

The Restore points are much more powerful than you think. Socket Error 10061 Connection Refused Windows 7 The problem was that sometimes the port-number of web service was changing unexpectedly. If you do not want to post the log publicly, you may email it to me.

AC for an ACARS message) that tells Plane Plotter what to do with the frame.

Socket Error # 10052: The host you were connected to crashed and rebooted. Is there a way to make a metal sword resistant to lava? If i retry on dialog, it works fine. Socket Error 10061 Error Number 0x800ccc0e share|improve this answer answered Dec 2 '14 at 8:12 isaeid 949 THANK YOU!

Our FTP is vsftpd 2.0.5-12.el5_3.1 on CentOS 5.3, fully updated. So then I simply imported a backup of the /mysql/ user data from my prior development environment and ran FLUSH PRIVILEGES in a phpMyAdmin SQL window. But I'm getting a 425 error, but it is "error 425 sorry, invalid address given" Have you any explanation for this error message and why is it the same error number? this contact form This error often occurs when you try to connect in PASV mode to a server that prefers PORT for data connections.

If you want to save a chart or outline display for retrieval with a single click, use the Quick Chart feature. If the error persists, ask in the Yahoo group (and I will put Bev's response here - better informed than mine!). and choose the button number that you want to associate with that chart display.